The Breitling Watch Source Forums

Breitling Watch Information Forums, Navitimer, Chronomat
It is currently Thu Mar 28, 2024 9:01 am

All times are UTC - 8 hours




Post new topic Reply to topic  [ 50 posts ]  Go to page 1, 2, 3, 4  Next
Author Message
 Post subject: The watch winder thread
PostPosted: Sat Oct 23, 2010 11:49 am 
Offline
Contributing Moderator
Contributing Moderator
User avatar

Joined: Fri Jul 27, 2007 5:09 am
Posts: 36521
Likes: 0 post
Liked in: 489 posts
Location: Ontario, Canada
Watch winders are one of the most asked about things on this forum so I thought that I would try and put together a post that answers all of the common questions. The basics aren’t actually that difficult, but they do seem to cause all kinds of confusion. As always feedback is appreciated and I’m sure that I’ll forget some of the questions so I’ll update this as I get a chance.

Let’s start with the basics.

A watch winder does not wind a watch! Watch winders are designed to prevent an automatic watch from winding down when not being worn. They rotate the watch causing the rotor to rotate and wind the mainspring. The number of rotations can generally be chosen from a series of programs and the idea is to choose a setting that is close to the number that the watch will need to add 24 hours of reserve to the mainspring (i.e. in a 24 hour period the winder adds as much power as the watch uses, effectively keeping the watch wound to the same extent). There are watch winders for manual wind watches but those are very specialised and aren’t considered here. Winders come individually or in combos up to 50 or more. Additionally, some winders allow for two watches on each head (more on that later).

Are winders bad for watches?

Subject to some of the advice given below, there is nothing damaging about winders. If the watch sits on a winder that is set correctly it will likely receive less wear than if it were being worn. While running the watch on the winder will cause more wear than if the watch were sitting not running, this isn’t really an issue. With modern watches the service period is dictated by the aging of the oils not excessive wear on movement parts.

Do I have to buy a winder?

No. If you wear your watch every day then leave it on the night stand at night and it will be fine the next day. You only need to consider a winder if you aren’t going to be wearing a watch for an extended period of time – close to or in excess of the power reserve. Even then, you don’t have to buy a winder – you have one at the end of each arm that will wind the watch perfectly adequately via the crown. Winders simply offer more convenience.

Why are some winders cheap and others cost a fortune?

Like everything else there are huge differences in the quality of winders from different manufacturers. There are many winders that contain Chinese motors that are generally low quality and contain plastic gears. These are inexpensive – sometimes under $50 on eBay and will wind the watch. However, they are frequently noisy out of the box or become noisy in a few months. They generally can’t be repaired, but they may last for several years (or just a few months). Buy them as consumables and you probably won’t be disappointed.

At the other end of the market there are winders with German or US motors and metal gears. Generally these also have a much better fit and finish elsewhere in the winder – the box, the cushions, etc. These aren’t immune from problems – the whole industry has a questionable track record, and can also become noisy over time. If you do have problems with these you generally have a fairly good warranty that you can fall back on, and they will be repairable if they fail after the warranty expires.

Both types of winders have advantages and disadvantages; it’s down to the individual to decide which way they want to go.

Why do people keep talking about rest periods?

Remember that the basic premise of a winder is that it will put as much reserve into the mainspring as the watch will use in a 24 hour period. That can be achieved in a number of ways – it can sit idle for 23 hours and 59 minutes and then spin like a propeller for a minute, or it can turn constantly at a slow speed for a full 24 hours. I think that most people will recognise that the first example isn’t a good idea, but neither is the second. If your winder doesn’t rest (and many don’t) then the mainspring is never being given an opportunity to wind down – it is constantly being kept at the same level, and if the watch is put on the winder straight off the wrist then that likely means that the mainspring is constantly kept fully wound – under the maximum tension. It’s like manually winding the watch constantly (but slowly). You want the mainspring to at least have a short period of being able to wind down and then get topped up to avoid excessive wear on the mainspring and barrel.

So how long a rest period do I need?

Winders come with many different rest periods – from just a couple of minutes to several hours. There is no right answer as to how long the rest period should be, but you do need to make sure that the rest period is enough to at least allow the mainspring to ease off from maximum tension. Personally I would never use a winder that has less than a 10 minute rest period. Winders with long (several hour) rest periods may cause the watch to stop if the reserve is low (the rest period allows the watch to completely run down).

What’s with clockwise, counter clockwise and both?

Automatic watches wind from the rotation of the rotor on the back of the movement. Some of them wind in only one direction, and some of them wind in both directions. Winders can generally be set to wind either clockwise all the time (for watches that only wind clockwise), counter clockwise all the time (for watches that only wind counter clockwise) or alternating between clockwise and counter clockwise (for watches that wind in both directions).

Watches that can be wound in both directions will also wind without any problems on a clockwise or counter clockwise program, but if your watch only winds in one direction then you need to set the winder correctly or the watch will not stay wound.

What are tpd?

Turns per day (tpd) are the number of rotations that the winder will give the watch. Some of the more basic winders have a fixed number of tpd, the better ones will be programmable for different numbers.

How do I know how many tpd and which direction my watch needs?

This is probably the most common question, and it’s probably the easiest to answer. One of the major winder manufacturers – Orbita, provides a database of watches and movements with information about how many tpd and which direction. The database can be found here - http://www.orbita.net/database-search/

Does it matter if my watch winder only has settings for more tpd than I need?

Within reason, no. If you were wearing your watch it would probably get more tpd than it needs to stay wound, but because automatic watches can’t be over wound it will be fine. If you have a watch that only needs 600tpd and your winder winds at 1,300tpd then I would look for a different winder, but if the lowest setting is 800tpd then you’ll be OK.

Does it matter if my watch winder only has settings for fewer tpd than I need?

Again, within reason you’ll be fine. If the winder doesn’t provide enough turns to keep the watch fully wound then the reserve will gradually reduce, but unless you leave the watch on the winder for extended periods it won’t be a practical problem. You should use the most turns as you can, but if your watch needs 800tpd and the winder can only provide 650tpd then the watch will still run for almost 10 days.

So how do I know how long it will run for if it has fewer tpd?

Are you sure you want to know – it means math!

OK, if you’re still reading……….

Assume that the watch is fully wound and that it’s a Breitling with a 42 hour power reserve. Let’s further assume that it needs 800tpd to keep it fully wound. That means that it needs 33.33 turns per hour (800/24). If it’s not getting 800 tpd then the watch will wind down, with the reserve being reduced by an hour for every 33.33 turns shortfall. Suppose that the winder is providing 650tpd, that means that the shortfall is 150tpd. That equates to a reserve reduction of around 4 1/2 hours (150/33.33). So after one day the reserve will be 37 1/2 hours (42 – 4 1/2), after two days it will be 33 hours (37 1/2 – 4 1/2), etc

Is it OK to use a winder that has two heads per motor?

There are a number of winders that have cushions for two watches on each motor to try and keep the costs down. It’s not a good idea to buy these (or at least to put two watches on them) if they use plastic gears. Unless the watches are identical the differences in weight and weight distribution will cause the gears to be unbalanced and with plastic gears that will quickly cause wear and parts failure. If your motor uses metal gears then there is less of a concern, but you should still try to use similar size and weight watches on each motor.

I put my watch on my winder but it’s not winding – why?

Remember that winders don’t wind watches – they keep them wound. If you put a watch that has completely run down on a winder then it will still be completely run down when you take it off. If the watch was fully wound when you put it on the winder and it stopped after the normal power reserve then it is probably a watch than only winds in one direction and the winder is set for the opposite direction.

If you had an extended reserve but it still stopped then either it is a watch that winds in only one direction and your winder is set for both directions (so only winding the watch half the time), or the turns per day are insufficient.

Which brand should I buy?

Whatever you want. I don’t like recommending specific winders, but if you find one you like then do a search for it here, chances are that someone has offered an opinion and their experiences of that make.

Why didn’t you answer my question?

Because I forgot about it – what do you need to know?



4 people like this post.
Top
 Profile  
Reply with quote  
PostPosted: Sat Oct 23, 2010 11:51 am 
Offline
Forum Sponsor
Forum Sponsor
User avatar

Joined: Wed Sep 19, 2007 10:10 am
Posts: 3665
Likes: 14 posts
Liked in: 343 posts
Location: Wisconsin
Thanks for the great post Roff.

_________________
Justin
Please contact me via PM for the contact details for Govberg Jewelers
Govberg is an AD for over 50 fine Swiss and German watch brands.
Visit them on the web at http://www.govbergwatches.com or call 800-528-8463


Top
 Profile  
Reply with quote  
PostPosted: Sat Oct 23, 2010 4:29 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Apr 04, 2010 3:26 am
Posts: 2241
Likes: 7 posts
Liked in: 24 posts
Location: Ireland
First time using this but Here goes!
:superbow:

_________________
Breanach78

A Few Breitlings.


Top
 Profile  
Reply with quote  
PostPosted: Sat Oct 23, 2010 5:44 pm 
Offline
All Roads lead to Breitling
All Roads lead to Breitling
User avatar

Joined: Sat Jan 09, 2010 6:01 pm
Posts: 8010
Likes: 3 posts
Liked in: 33 posts
Awesome. Appreciate the effort and new resourse.

But I stopped reading at the math part. :huh

_________________
SHARKMAN


Top
 Profile  
Reply with quote  
PostPosted: Sat Oct 23, 2010 7:02 pm 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Fri Dec 04, 2009 4:21 am
Posts: 893
Likes: 0 post
Liked in: 1 post
Location: RPV, CA & Jakarta, Indonesia
Ah, but what's the effect and relationship of temperature, humidity, the seasons, and meteoric rain showers have on the tpd, rest period, and power reserve, huh? And how about equatorial positional effect? After all, some toilets flush clockwise, and some anti-clockwise depending on which side of the equator you're on, right? :?:

Otherwise really nice guide Prof! :mrgreen:

_________________
a few Pams... :mrgreen:


Top
 Profile  
Reply with quote  
PostPosted: Sun Oct 24, 2010 12:58 am 
Offline
Breitling Maniac
Breitling Maniac
User avatar

Joined: Sun Aug 08, 2010 10:30 am
Posts: 1287
Likes: 0 post
Liked in: 0 post
Location: BC Canada
Great job Roff.

A toilet... that flushes? What? Where? When? Huh?


Top
 Profile  
Reply with quote  
PostPosted: Sun Oct 24, 2010 7:26 am 
Offline
Contributing Member
Contributing Member

Joined: Tue Oct 02, 2007 5:30 am
Posts: 1126
Likes: 32 posts
Liked in: 12 posts
Location: Central Coast, NSW
Great post Roff. Just to add my little tip, if you have a winder that does more TPD than you need simply put it on a timeswitch. I sat and calculated how many TPD I needed as a minimum and then set my 24 hour timeswitch to switch the winder on and off to compensate, it now has 2 or 3 periods per 24 hours where it stops completely for a couple of hours.

Since doing this I've found my watches seem to run more accurately over all, purely coincidental I think as I can't see what bearing reducing the 'over winding' would have.

Incidentally Breitling UK's vintage watchmaker has told me there is absolutely no problem with keeping a vintage Chrono-Matic on the winder too.

Stef

_________________
Image


Last edited by Stefan Tapp on Sun Oct 24, 2010 9:11 am, edited 1 time in total.

Top
 Profile  
Reply with quote  
PostPosted: Sun Oct 24, 2010 8:09 am 
Offline
Breitling Fanatic
Breitling Fanatic

Joined: Mon Jun 01, 2009 8:58 am
Posts: 495
Likes: 4 posts
Liked in: 0 post
Location: Astoria, NY
Good Stuff 2 Know!

Thanks!!!

Best Regards,

Enezdez

_________________
IWC - Big Pilot 5002 - 01
IWC - Pilot Chrono 3717 - 04
Panerai - 183
Omega - Speedmaster 145.012 / 67
Rolex - Explore II (Black Dial) - 216570
Rolex - Explore I 114270
Blancpain FF 5015


Top
 Profile  
Reply with quote  
PostPosted: Sun Oct 24, 2010 10:26 am 
Offline
King of Ling
King of Ling
User avatar

Joined: Mon Jun 16, 2008 3:54 am
Posts: 1609
Likes: 17 posts
Liked in: 7 posts
Location: Scotland
Brilliant Roff, great post! Bet you'll still be answering the same old questions tho! :D

Cheers

_________________
:fulllingclub:
Currently:
Avenger Skyland(Black)
Super Avenger(White)

Moved on:
Montbrillant Legende(Silver)
Panerai 312

SOHC 125th Ann. LE(Silver)
Navitimer World(Pearl)
Panerai 441


Top
 Profile  
Reply with quote  
PostPosted: Sun Oct 24, 2010 11:25 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Jan 11, 2009 5:02 pm
Posts: 2200
Likes: 20 posts
Liked in: 13 posts
Location: Fort Worth, Texas
Thanks for taking the time Roff. I always enjoy learning something new, particularly concerning watches and I thoroughly enjoyed the read. Great stuff :thumbsup:

_________________
Happines is Good Health and a Bad Memory.
"Ingrid Bergman"


Top
 Profile  
Reply with quote  
PostPosted: Sun Oct 24, 2010 11:47 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sun Apr 04, 2010 3:26 am
Posts: 2241
Likes: 7 posts
Liked in: 24 posts
Location: Ireland
Stefan Tapp wrote:
Great post Roff. Just to add my little tip, if you have a winder that does more TPD than you need simply put it on a timeswitch. I sat and calculated how many TPD I needed as a minimum and then set my 24 hour timeswitch to switch the winder on and off to compensate, it now has 2 or 3 periods per 24 hours where it stops completely for a couple of hours.

Since doing this I've found my watches seem to run more accurately over all, purely coincidental I think as I can't see what bearing reducing the 'over winding' would have.

Incidentally Breitling UK's vintage watchmaker has told me there is absolutely no problem with keeping a vintage Chrono-Matic on the winder too.

Stef

:yeahthat I also worked out what I needed (TPD) and used a timer to compensate. I also feel that if set to be off over night it will replicate how a watch on the wrist would be. I.E. off the wrist at night or else not moved much throughout sleep!!!

_________________
Breanach78

A Few Breitlings.


Top
 Profile  
Reply with quote  
PostPosted: Mon Oct 25, 2010 2:10 am 
Offline
Forum Sponsor
Forum Sponsor

Joined: Thu Jun 03, 2010 5:34 am
Posts: 990
Likes: 0 post
Liked in: 2 posts
A brilliant resource Prof.

Thanks for taking the time and effort to put this together.

_________________
Forum Representative for Andrew Michaels Jewellers, UK

Please visit my Watch Blog at http://www.AndrewMichaels.co.uk

******Our new Pre-owned watch site www.amjwatches.co.uk is now live*****


Top
 Profile  
Reply with quote  
PostPosted: Mon Oct 25, 2010 1:46 pm 
Offline
Breitling Connoisseur
Breitling Connoisseur
User avatar

Joined: Tue Sep 21, 2010 2:12 pm
Posts: 594
Likes: 0 post
Liked in: 0 post
Location: Montana, USA
Great post Roff and some excellent information here. Thank you for taking the time to write this up and sharing with us. :uhmmm: Now to decide on which one and how many motors. Oh well another excuse to appease my growing WIS affliction. :boingb:

_________________
Image


Top
 Profile  
Reply with quote  
PostPosted: Wed Oct 27, 2010 8:58 am 
Offline
Contributing Member
Contributing Member
User avatar

Joined: Sat Jan 09, 2010 10:34 am
Posts: 965
Likes: 0 post
Liked in: 0 post
Location: Newtown, PA
Great post Roff. Good stuff and an awesome resource for the multitude of winder questions. I bet this thread will get some good "copy and paste" action.

_________________
“The only reason for time is so that everything doesn't happen at once.” - Albert Einstein


Top
 Profile  
Reply with quote  
PostPosted: Thu Apr 12, 2012 8:18 am 
Offline
Breitling Enthusiast
Breitling Enthusiast

Joined: Tue Mar 20, 2012 10:45 pm
Posts: 21
Likes: 0 post
Liked in: 0 post
Great post...

But what about the ones that only give you a time its spinning.. not tpd ?

Are they any good?

Here is the specs on the one I have scoped out on ebay... Little concern it would run all night?

Mode A (Counter-clockwise):
The turning plates will rotate counter-clockwise for 6 minutes and then pause for 30 minutes. (repeat)

Mode B (Clockwise): The turning plates will rotate clockwise for 6 minutes and then pause for 30 minutes. (repeat)

Mode C (Automatic):
The turning plates will rotate counter-clockwise for 20 minutes and then pause for 10 minutes; winds clockwise for 20 minutes and then pause for 10 minutes. (repeat)


Top
 Profile  
Reply with quote  

Display posts from previous:  Sort by  
Post new topic Reply to topic  [ 50 posts ]  Go to page 1, 2, 3, 4  Next

All times are UTC - 8 hours


Who is online

Users browsing this forum: No registered users and 10 guests


You cannot post new topics in this forum
You cannot reply to topics in this forum
You cannot edit your posts in this forum
You cannot delete your posts in this forum
You cannot post attachments in this forum

Jump to:  
 




Powered by phpBB® Forum Software © phpBB Group