| The Breitling Watch Source Forums https://breitlingsource.com/phpBB2/ |
|
| Bergeon "modified" tool!!!! https://breitlingsource.com/phpBB2/viewtopic.php?f=1&t=17603 |
Page 1 of 1 |
| Author: | geralder [ Sat Mar 13, 2010 4:06 pm ] |
| Post subject: | Bergeon "modified" tool!!!! |
Well, you may have seen my other thread on bracelet/strapo changing and how not to scratch my case back/lug area that is in inevitable. I took my Bergeon 6767-f tool and took the bit off the tool and the extra bit it comes with and a pair of snap ring pliers (available at any hardware store) and made a pair of spring bar pliers!!! No more scratching the case back/ lug area... your welcome! 
|
|
| Author: | FEAR [ Sat Mar 13, 2010 4:28 pm ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
pics! |
|
| Author: | geralder [ Sat Mar 13, 2010 8:41 pm ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
I took these snap ring/retaing pliers and put the Bergeon 6767-f tips on the end . I spent $15 on this tool. The actual Bergeon spring bar pliers are $145!!!   
|
|
| Author: | Huttfuzz [ Sat Mar 13, 2010 11:18 pm ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
That is nice. |
|
| Author: | Redpross [ Sun Mar 14, 2010 4:21 am ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
Why don't Bergeon just put a plastic or rubber coating on the tip to stop it scratching? Is that to simplistic? |
|
| Author: | geralder [ Sun Mar 14, 2010 8:13 am ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
Well, its not the tool that scratches its the spring bar or the strap alignment. With the 6767-f tool one end of the spring bar is exposed while trying to engage to the other end. |
|
| Author: | MartC [ Sun Mar 14, 2010 10:59 am ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
Nice idea, its good to see people thinking differently and modding stuff  I just tape up the case lugs when changing straps 
|
|
| Author: | dhalem [ Sun Mar 14, 2010 11:24 am ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
Yeah, I posted this a while back. Someone else had the same idea: http://forums.timezone.com/index.php?t= ... 1342&rid=0 |
|
| Author: | geralder [ Sun Mar 14, 2010 12:08 pm ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
I dont like the whole duct tape thing
|
|
| Author: | dhalem [ Sun Mar 14, 2010 12:46 pm ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
geralder wrote: I dont like the whole duct tape thing Me neither. I was gonna do one with epoxy. |
|
| Author: | geralder [ Sun Mar 14, 2010 1:14 pm ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
Hahaha. The nice thing is the Bergeon bits thread in, so they are held tight and secure during strap/bracelet chages. |
|
| Author: | dhalem [ Sun Mar 14, 2010 4:05 pm ] |
| Post subject: | Re: Bergeon "modified" tool!!!! |
Oh, that is nice. I'll have to run over to Otto Frei and get some tips. |
|
| Page 1 of 1 | All times are UTC - 8 hours |
| Powered by phpBB® Forum Software © phpBB Group https://www.phpbb.com/ |
|